VLANs

From Ever changing code
Revision as of 21:43, 10 April 2015 by Pio2pio (talk | contribs) (→‎Native VLAN)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

VLAN setup

Basic VLANs info. Cisco series 1900 routers support up to 16 VLANs.

Create
#vlan vlan_id
Deleting a VLAN
#no vlan vlan_id
Show all VLANs summary and port assignment
s1# show vlan brief          !a switch command
r1# show vlan-switch         !a router command

VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
1    default                          active    Gi0/1/0, Gi0/1/1, Gi0/1/2
                                                Gi0/1/3
1002 fddi-default                     act/unsup
1003 token-ring-default               act/unsup
1004 fddinet-default                  act/unsup
1005 trnet-default                    act/unsup

VLAN Type  SAID       MTU   Parent RingNo BridgeNo Stp  BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1    enet  100001     1500  -      -      -        -    -        1002   1003
1002 fddi  101002     1500  -      -      -        -    -        1      1003
1003 tr    101003     1500  1005   0      -        -    srb      1      1002
1004 fdnet 101004     1500  -      -      1        ibm  -        0      0
1005 trnet 101005     1500  -      -      1        ibm  -        0      0

Access port configuration

interface GigabitEthernet1/0/2
description Access Port to Cisco Access Point
switchport access vlan 10
no ip address
end
interface range
interface range gi 0/1/0 - 3

Trunk port configuration

For 802.1Q trunking, one VLAN is not tagged. This VLAN is called native VLAN. The native VLAN is used for untagged traffic when the port is in 802.1Q trunking mode. While configuring 802.1Q trunking, it is very important to keep in mind that the native VLAN must be configured the same on each side of the trunk link. It is a common mistake not to match the native VLANs while configuring 802.1Q trunking between the router and the switch.

In this example 802.1Q encapsulation is used

interface GigabitEthernet1/0/1
description Trunk Port to Cisco WLC
switchport trunk encapsulation dot1q
switchport mode trunk !changes to permanent trunking mode, the port enters into a Dynamic Trunking Protocol (DTP) negotiation 
                      !to convert the link into a trunk link even if the interface connecting to it does not agree to the change.
switchport trunk native vlan 99
switchport trunk allowed vlan add 10,20,99
switchport nonegotiate
no shutdown

The following list shows options for the switchport mode command.

trunk - configures the port into permanent 802.1Q trunk mode and negotiates with the connected device to convert the link to trunk mode.
access - disables port trunk mode and negotiates with the connected device to convert the link to nontrunk.
nonegotiate - the port is a trunk and does not do DTP negotiation with the other side of the link.
dynamic desirable - triggers the port to negotiate the link from nontrunk to trunk mode. The port negotiates to a trunk port if the connected device is in trunk state, desirable state, or auto state. Otherwise, the port becomes a nontrunk port.
dynamic auto - enables a port to become a trunk only if the connected device has the state set to trunk or desirable. Otherwise, the port becomes a nontrunk port.

Verifying a Trunk

switch# show interfaces trunk                    !can be issued on a router or switch

Port      Mode         Encapsulation  Status        Native vlan
Gi0/1/0   on           802.1q         trunking      99
Gi0/1/1   on           802.1q         trunking      99
Gi0/1/2   on           802.1q         trunking      99
Gi0/1/3   on           802.1q         trunking      99

Port      Vlans allowed on trunk
Gi0/1/0   1,10,20,99,1002-1005
Gi0/1/1   1,10,20,99,1002-1005
Gi0/1/2   1,10,20,99,1002-1005
Gi0/1/3   1,10,20,99,1002-1005

Port      Vlans allowed and active in management domain
Gi0/1/0   1,10,20,99
Gi0/1/1   1,10,20,99
Gi0/1/2   1,10,20,99
Gi0/1/3   1,10,20,99

Port      Vlans in spanning tree forwarding state and not pruned
Gi0/1/0   1,10,20,99
Gi0/1/1   1,10,20,99
Gi0/1/2   1,10,20,99

Port      Vlans in spanning tree forwarding state and not pruned
Gi0/1/3   1,10,20,99
Switch# show interfaces GigabitEthernet1/0/1 switchport
Switch# show interfaces GigabitEthernet1/0/1 trunk

DTP (Dynamic Trunking Protocol)

DTP is used to automatically form a trunk between switches. Default DTP setting is dependent on the IOS software version and platform used. DTP is a Cisco proprietary protocol. Therefore some network devices might forward DTP frames improperly, which can cause misconfigurations. To avoid this, turn off DTP on interfaces on a Cisco switch connected to devices that do not support DTP/connected to 3rd party hardware.

The operation of DPT can be verified by issuing show dtp interface. Output below shows that Trunk Operational Status (TOS) is set to trunk, Trunk Administrative Status (TAS) is desirable, and Trunk Negotiation Status (TNS) is also set to trunk. Trunk Operational Type (TOT), Trunk Adminstrative Type (TAT), and Trunk Negotiation Type (TNT) show 802.1q encapsulation. Output below is from Cisco 1941 IOS Version 15.2(4)M4 with EHWIC-4ESG-P Ether-switch card that does not support DTP. Therefore the output you can see 'NONEGOTIATE' and timers with zero.

Switch#show dtp interface Gi0/1/0
DTP Interface Information:
  TOS/TAS/TNS:                           TRUNK/NONEGOTIATE/TRUNK
  TOT/TAT/TNT:                           802.1Q/802.1Q/802.1Q
  Neighbor address 1:                    000000000000
  Neighbor address 2:                    000000000000
  Hello timer expiration ms/state:       0/STOPPED
  Access timer expiration ms/state:      0/STOPPED
  Negotiation timer expiration ms/state: 0/STOPPED
  Multidrop timer expiration ms/state:   0/STOPPED
  FSM state:                             S6:TRUNK
  # times multi & trunk:                 0
  Enabled:                               1
  In STP:                                0
trunk - automatically enables trunking regardless of the state of the neighboring switch and regardless of any DTP requests that are sent from the neighboring switch.
access - trunking is not allowed on this port regardless of the state of the neighboring switch interface and regardless of any DTP requests that are sent from the neighboring switch.
nonegotiate - prevents the interface from generating DTP frames. This command can be used only when the interface switch port mode is access or trunk. You must manually configure the neighboring interface as a trunk interface to establish a trunk link.
dynamic desirable - communicates to the neighboring switch via DTP that the interface is attempting to become a trunk if the neighboring switch interface is able to become a trunk.
dynamic auto - creates the trunk based on the DTP request from the neighboring switch. Interface will become a trunk interface if the neighboring iface is set to trunk or desirable mode
DTP-mode-matrix
Nonegotiate mode operation

The switchport nonegotiate interface command stops DTP negotiation packets sending and engaging in trunk election. This command is valid only when the interface switch port mode is access or trunk. This command returns an error if you attempt to execute it in dynamic (auto or desirable) mode. When in nonegotiate configuration, the port trunks only if the other end of the link is specifically set to trunk. The switchport nonegotiate command does not form a trunk link with ports in either dynamic desirable or dynamic auto mode.

Native VLAN

Tagged Frames on the Native VLAN - are discarded

Some devices that support trunking, add a VLAN tag to native VLAN traffic. Control traffic sent on the native VLAN should not be tagged. If an 802.1Q trunk port receives a tagged frame with the VLAN ID the same as the native VLAN, it drops the frame. Consequently, when configuring a switch port on a Cisco switch, configure devices so that they do not send tagged frames on the native VLAN. Devices from other vendors that support tagged frames on the native VLAN include IP phones, servers, routers, and non-Cisco switches.

Untagged Frames on the Native VLAN

When a Cisco switch trunk port receives untagged frames (which are unusual in a well-designed network), it forwards those frames to the native VLAN. If there are no devices associated with the native VLAN (which is not unusual) and there are no other trunk ports (which is not unusual), then the frame is dropped. The default native VLAN is VLAN 1. When configuring an 802.1Q trunk port, a default Port VLAN ID (PVID) is assigned the value of the native VLAN ID. All untagged traffic coming in or out of the 802.1Q port is forwarded based on the PVID value. For example, if VLAN 99 is configured as the native VLAN, the PVID is 99 and all untagged traffic is forwarded to VLAN 99. If the native VLAN has not been reconfigured, the PVID value is set to VLAN 1.

Troubleshooting

Lack of connectivity - missing VLAN
  1. Make sure your devices have correct ip addresses in correct subnets
  2. Check whether ports are a members of the correct VLAN show vlan
  3. Issue show interfaces switchport and search for Inactive means that the VLAN has been deleted from vlan.dat file and needs recreating. This is because each port in a switch belongs to a VLAN.
Trunk link troubleshooting
  1. Native VLAN check - use show interfaces trunk at both ends to check whether a native VLAN matches on both sites. If not VLAN leaking occurs meaning that port can accept frames form a different VLAN that is assigned to. If CDP is enabled it will display %CDP-4-NATIVE_VLAN_MISMATCH message.
    In a native VLAN mismatch scenario connectivity issues occur in the network if a native VLAN mismatch exists. Data traffic for VLANs, other than the two native VLANs configured, successfully propagates across the trunk link, but data associated with either of the native VLANs does not successfully propagate across the trunk link.
  2. Trunk status - use show interfaces trunk at both ends. If possible configure interfaces to trunk mode. Cisco Catalyst switch ports use DTP by default and attempt to negotiate a trunk link.
  3. Allowed VLANs on trunk - use show interfaces trunk to see allowed VLANs on the trunk link. There can be missing or not allowed VLAN causing the problem.

Security - control traffic

All control traffic is sent on VLAN 1. Therefore, when the native VLAN is changed to something other than VLAN 1, all control traffic is tagged on IEEE 802.1Q VLAN trunks (tagged with VLAN ID 1). A recommended security practice is to change the native VLAN to a different VLAN than VLAN 1.