Cisco 878

From Ever changing code
Revision as of 13:19, 15 December 2013 by Pio2pio (talk | contribs) (→‎References)
Jump to navigation Jump to search

Product codding

The highest IOS version available for this platform is c870-advsecurityk9-mz.151-4.M6.bin

Current product in test
show inventory
NAME: "878", DESCR: "878 chassis, Hw Serial#: ******604F, Hw Revision: 0x300"
PID: CISCO878-K9         , VID: V04 , SN: *******604F

show hardware
Cisco IOS Software, C870 Software (C870-ADVSECURITYK9-M), Version 12.4(4)T, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Thu 27-Oct-05 09:42 by ccai

ROM: System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE

home-r1 uptime is 38 minutes
System returned to ROM by power-on
System image file is "flash:c870-advsecurityk9-mz.124-4.T.bin"

<-- output omitted -->

Cisco 878 (MPC8272) processor (revision 0x300) with 118784K/12288K bytes of memory.
Processor board ID ******604F
MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
4 FastEthernet interfaces
1 ISDN Basic Rate interface
128K bytes of non-volatile configuration memory.
24576K bytes of processor board System flash (Intel Strataflash)

Configuration register is 0x2102

DSL support

Cisco 878-K9 platform has build in modem based on ST-Microelectronics 20190 Chipset

  • Supports ADSL over basic telephone service with Annex A and Annex B ITU G. 992.1 (ADSL), G.992.3 (ADSL2), and G.992.5 (ADSL2+)
  • Supports ADSL over basic telephone service with Annex M (except UK Mask) (extended upstream bandwidth) G.992.3 (ADSL2) and G.992.5 (ADSL2+)
  • G.994.1 ITU G.hs
  • Support for Reach-extended ADSL2 (G.922.3) Annex L
  • Complies with T1.413 ANSI ADSL DMT issue 2
  • DSL Forum TR-067
  • The chipset does not provide interoperability with carrierless amplitude modulation/phase modulation (CAP)-based ADSL lines
  • Annex A and Annex B are supported starting with Cisco IOS Software Release 12.4(4)T.
  • Annex M (except UK Mask) is supported starting with the special Cisco IOS Software Release 12.4(11)XJ; and requires the CISCO877-M-K9 or CISCO877W-G-E-M-K9 SKU.
  • The ADSL2 standard (ITU G.992.3) adds new features and functions targeted at improving ADSL performance and interoperability. In addition, the standard adds support for new applications, services, and deployment scenarios. Among the changes are improvements in data rate and reach performance, rate adaptation, improved diagnostics, and power enhancements. The conventional ADSL standard (ITU G.992.1) provides downstream data rates of up to 8 Mbps and upstream data rates of up to 0.8 Mbps, and ADSL2 provides higher downstream rates of up to 12 Mbps and upstream data rates of up to 1 Mbps.
  • The ADSL2+ standard (ITU G.992.5) doubles the bandwidth used for downstream data transmission, effectively doubling the maximum downstream data rates, and achieving downstream data rates of up to 24 Mbps and upstream data rates of up to 1.5 Mbps.
  • Cisco 877-M supports ITU G.992.3 Annex M (except UK Mask), and is optimized for PSD Mask EU-64 M9. Annex M adds capabilities for extended upstream bandwidth above 2.0Mbps. This allows carriers and enterprises to cover applications traditionally served by T1, E1, G.SHDSL without overhauling the transport infrastructure. Exact data rates vary depending on the distance from the DSL access multiplexer (DSLAM), DSLAM type, line card and chipset, and firmware, noise profile, quality of copper, etc. The reach-extended ADSL2 standard (G.992.3)
  • Annex L increases performance on loop lengths greater than 16,000 feet from the Central Office.

References

Retrieved from ‘http://wiki.ciscolinux.co.uk/index.php?title=Cisco_878&oldid=764’