Difference between revisions of "Cisco 1941 with EHWIC-VA-DSL-M"
Jump to navigation
Jump to search
| Line 74: | Line 74: | ||
*[http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/oview_ic.html Overview of Cisco Interface Cards for Cisco Access Routers] It explains EHWIC, HWIC, WIC cards differences | *[http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/oview_ic.html Overview of Cisco Interface Cards for Cisco Access Routers] It explains EHWIC, HWIC, WIC cards differences | ||
*[http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/software/configuration/guide/pppoanatfm.html Configuring PPP over ATM with NAT] | *[http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/software/configuration/guide/pppoanatfm.html Configuring PPP over ATM with NAT] | ||
*[http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/software/configuration/guide/routconf_ps9572_TSD_Products_Configuration_Guide_Chapter.html#wp1130490 Basic Router Configuration] | *[http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/software/configuration/guide/routconf_ps9572_TSD_Products_Configuration_Guide_Chapter.html#wp1130490 Basic Router Configuration] See Configuring VDSL Auto Mode & verify | ||
*[http://www.cisco.com/en/US/prod/collateral/routers/ps380/qa_c67-612339.html Cisco 880VA Series ISR G2 Multimode DSL Routers] Our module EHWIC-VA-DSL-M card supports the same DSL and ATM features and modem firmware as available for the Cisco 880VA Series. | |||
Revision as of 22:23, 29 September 2013
Product codding
Cisco Multimode VDSL2 and ADSL2/2+ High-Speed WAN Interface Card
Product: EHWIC-VA-DSL-M
Description: 1-port VDSL2/ADSL2+ EHWIC over POTS with Annex M
Minimum IOS: 15.1(3)T
VDSL2 (very high speed DSL)
/ Digital Subscriber Line
/ /
EHWIC-VA-DSL-M
\ \ \Annex M
\ ADSL2/A2+ (asymmetric DSL)
Enhanced High-Speed WAN Interface Card
show inventory NAME: "CISCO1941/K9", DESCR: "CISCO1941/K9 chassis, Hw Serial#: FCZ1727C5JE, Hw Revision: 1.0" PID: CISCO1941/K9 , VID: V05 , SN: *********** NAME: "ADSL/VDSL over POTS Annex M supporting ADSL1, ADSL2, ADSL2+ and VDSL2 on Slot 0 SubSlot 1", DESCR: "ADSL/VDSL over POTS Annex M supporting ADSL1, ADSL2, ADSL2+ and VDSL2" PID: EHWIC-VA-DSL-M , VID: V01 , SN: ***********
LED explained
| LED | Color | Description |
|---|---|---|
| EN | Green | Operating system is running. |
| Amber | Interface card is resetting. | |
| Blinking | System is initializing. | |
| CD LED | Green | Lit when the unit is connected to the network and operating normally. On ADSL interface cards only, this LED blinks while training with DSLAMs. |
| LP LED | Yellow | DSL interface is in loopback mode. |
| Off | Normal operation. |
Config prep
! clean start by removing current config erase startup-config reload
Current platform info at the boot
Cisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory. Processor board ID FCZ1727C5JE 1 DSL controller 1 Ethernet interface 2 Gigabit Ethernet interfaces 1 ATM interface 3 terminal lines 2 Cellular interfaces DRAM configuration is 64 bits wide with parity disabled. 255K bytes of non-volatile configuration memory. 250880K bytes of ATA System CompactFlash 0 (Read/Write)
! initiate xDSL card, it's added automatically controller VDSL 0/1/0
References
- Cisco Multimode VDSL2 and ADSL2/2+ High-Speed WAN Interface Card
- Cisco Multimode VDSL2 and ADSL2/2+ EHWIC Q&A
- Connecting DSL WAN Interface Cards
- Overview of Cisco Interface Cards for Cisco Access Routers It explains EHWIC, HWIC, WIC cards differences
- Configuring PPP over ATM with NAT
- Basic Router Configuration See Configuring VDSL Auto Mode & verify
- Cisco 880VA Series ISR G2 Multimode DSL Routers Our module EHWIC-VA-DSL-M card supports the same DSL and ATM features and modem firmware as available for the Cisco 880VA Series.