Difference between revisions of "Cisco 1941 with AIR-SAP 1602E-E-K9 Standalone"

From Ever changing code
Jump to navigation Jump to search
Line 162: Line 162:
  !
  !
  end
  end
==== Where is AP management? is WLC missing on ISR G2 routers? ====
SRE is needed to provide WLC functionality. You can read more about it following this link [http://www.cisco.com/en/US/prod/collateral/modules/ps10598/data_sheet_c78-553913.html Cisco Services-Ready Engine]. It is worth it to mention that Cisco 1941 ISR G2 router can support only '''1x Cisco SRE Internal Services Module (ISM)'''.
;These applications but not limited are supported on Cisco SRE Modules:
*'''Network services:''' Cisco Wireless LAN Controller (WLC), Infoblox Core Network Services, Cisco Prime™ Network Analysis Module (NAM), NetScout nGenius Integrated Agent, BlueCat Adonis DNS/DHCP and Proteus IPAM, LogLogic MX-Virtual Appliance, Visual Network Systems OmniPoint Element, Uplogix Local Management Platform
*'''Application services:''' Cisco Wide Area Application Services (WAAS), Cisco UCS Express,  Cisco Application Extension Platform (AXP)
*'''Security:'''  Cisco Video Surveillance, SecureLogix Voice Policy Firewall


=== References ===
=== References ===

Revision as of 20:19, 20 October 2013

Here below you will find a basic configuration of AIR-SAP 1602E-E-K9 access point connected to 4-port EHWIC card inserted into Cisco 1941 ISR G2 modular router.

Product codding

Product/Model Number: AIR-SAP1602E-E-K9
IOS C1600 Software (AP1G2-K9W7-M), Version 15.2(2)JB2, RELEASE SOFTWARE (fc1)

                Regulatory Domain
               /
AIR-SAP 1602E-E-K9
     \       \_External antenna
      \_C_ stands for: Control and Provisioning of Wireless Access Points Protocol CAPWAP require WLC (Wireless Lan Controller)
       \_S_ stands for: Standalone AP
Router show inventory
#show inventory
NAME: "CISCO1941/K9", DESCR: "CISCO1941/K9 chassis, Hw Serial#: ***********, Hw Revision: 1.0"
PID: CISCO1941/K9      , VID: V05 , SN: ***********
NAME: "3G WWAN EHWIC-QuadBand HSPA+R7/HSPA/UMTS QuadBand EDGE/GPRS and GPS on Slot 0 SubSlot 0", DESCR: "3G WWAN EHWIC-QuadBand HSPA+R7/HSPA/UMTS QuadBand  EDGE/GPRS and GPS"
PID: EHWIC-3G-HSPA+7   , VID: V01 , SN: ***********
NAME: "Modem 0 on Cellular0/0/0", DESCR: "Sierra Wireless MC8705"
PID: MC8705            , VID: 1.0, SN: ***********
NAME: "4 Port GE POE EHWIC Switch on Slot 0 SubSlot 1", DESCR: "4 Port GE POE EHWIC Switch"
PID: EHWIC-4ESG-P      , VID: V01 , SN: ***********
NAME: "C1941 AC-POE Power Supply", DESCR: "C1941 AC-POE Power Supply"
PID: PWR-1941-POE      , VID:    , SN:
Access point show inventory
NAME: "AP1600", DESCR: "Cisco Aironet 1600 Series (IEEE 802.11n) Access Point"
PID: AIR-SAP1602E-E-K9 , VID: V01, SN: ********x11

Please notice that access points are powered by Power Over Ethernet. There is a difference power consumption for AIR-CAP (managed) access point that uses 13W vs AIR-SAP (standalone) uses 15.4W. 

#sh power inline
PowerSupply   SlotNum.   Maximum   Allocated       Status
-----------   --------   -------   ---------       ------
INT-PS           0        80.000    46.200         PS GOOD
Interface   Config   Device   Powered    PowerAllocated   State
---------   ------   ------   -------    --------------   -----
Gi0/1/0     auto     Unknown  Off        0.000 Watts      NOT_PHONE
Gi0/1/1     auto     IEEE-3   On        15.400 Watts      PHONE
Gi0/1/2     auto     IEEE-3   On        15.400 Watts      PHONE
Gi0/1/3     auto     IEEE-3   On        15.400 Watts      PHONE
Default account credentials on the access point
Username: Cisco
Password: Cisco
Enabled mode: Cisco

Basic AP config with WPA2-PSK auth

! Last configuration change at 01:27:06 UTC Mon Mar 1 1993 by tech
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
!please change name as required
hostname ap1
!
!
logging rate-limit console 9
!
aaa new-model
!
!
aaa authentication login default local
aaa authorization exec default local
!
!
!
!
!
aaa session-id common
no ip routing
no ip cef
!
!
!
dot11 syslog
!
dot11 ssid DS_WPA2
   authentication open
   authentication key-management wpa version 2
   guest-mode
   infrastructure-ssid optional
   !set password as required
   wpa-psk ascii WPA2_password
!
!
crypto pki token default removal timeout 0
!
!
username Cisco password 7 00271A150754
username tech privilege 15 secret tech
!
!
bridge irb
!
!
!
interface Dot11Radio0
 no ip address
 no ip route-cache
 !
 encryption mode ciphers aes-ccm
 !
 ssid DS_WPA2
 !
 antenna gain 0
 stbc
 beamform ofdm
 station-role root
 bridge-group 1
 bridge-group 1 subscriber-loop-control
 bridge-group 1 spanning-disabled
 bridge-group 1 block-unknown-source
 no bridge-group 1 source-learning
 no bridge-group 1 unicast-flooding
!
interface Dot11Radio1
 no ip address
 no ip route-cache
 shutdown
 antenna gain 0
 no dfs band block
 channel dfs
 station-role root
 bridge-group 1
 bridge-group 1 subscriber-loop-control
 bridge-group 1 spanning-disabled
 bridge-group 1 block-unknown-source
 no bridge-group 1 source-learning
 no bridge-group 1 unicast-flooding
!
interface GigabitEthernet0
 no ip address
 no ip route-cache
 duplex auto
 speed auto
 bridge-group 1
 bridge-group 1 spanning-disabled
 no bridge-group 1 source-learning
!
interface BVI1
 ip address dhcp client-id GigabitEthernet0
 no ip route-cache
!
ip forward-protocol nd
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
!
!
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
 transport input all
!
end

References

Retrieved from ‘http://wiki.ciscolinux.co.uk/index.php?title=Cisco_1941_with_AIR-SAP_1602E-E-K9_Standalone&oldid=436’