Cisco WLC 2504
Revision as of 21:30, 5 March 2014 by Pio2pio (talk | contribs) (→Upgrade WLC software using cli method)
License applying
Here we will be applying AP count license to add additional 25 access points to base image. It may happen that you need to remove base count license
(Cisco Controller) >license install tftp: url is invalid. Use tftp://<server ip>/path/filename (Cisco Controller) >license install tftp://10.10.10.2/PSZAABBCCDD_20140103032222.lic Transfering licenses from tftp://10.10.10.2/PSZAABBCCDD_20140103032222.lic 1/3 licenses were successfully installed 2/3 licenses were existing licenses 0/3 licenses were failed to install Failed license installation at index:0 : Duplicate license Failed license installation at index:1 : Duplicate license
- Verify
Please believe the last line was showing 25, now it is 50.
(Cisco Controller) show>sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.3.101.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... Cisco_aa:bb:cc
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 10.10.10.1
Last Reset....................................... Power on reset
System Up Time................................... 0 days 4 hrs 1 mins 19 secs
System Timezone Location.........................
Configured Country............................... GB - United Kingdom
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +26 C
External Temperature............................. +30 C
Fan Status....................................... 4300 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 84:78:AC:AA:BB:CC
Maximum number of APs supported.................. 50
Upgrade WLC software using cli method
(Cisco Controller) >transfer download mode tftp (Cisco Controller) >transfer download serverip 10.10.10.3 (Cisco Controller) >transfer download path ./ (Cisco Controller) >transfer download filename AS_5500_7_5_102_9.aes (Cisco Controller) >transfer download start Mode............................................. TFTP Data Type........................................ Code TFTP Server IP................................... 10.10.10.3 TFTP Packet Timeout.............................. 6 TFTP Max Retries................................. 10 TFTP Path........................................ ./ TFTP Filename.................................... AS_5500_7_5_102_9.aes This may take some time. Are you sure you want to start? (y/N) y TFTP Code transfer starting. TFTP receive complete... extracting components. Image version check passed. Executing backup script. Writing new RTOS to flash disk. Writing new FP to flash disk. Writing new AP Image Bundle to flash disk. Executing fini script. TFTP File transfer is successful. Reboot the controller for update to complete. Optionally, pre-download the image to APs before rebooting to reduce network downtime.
- Verify version
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.220.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... Cisco_31:59:44
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 10.10.10.2
Last Reset....................................... Power on reset
System Up Time................................... 0 days 6 hrs 34 mins 19 secs
System Timezone Location.........................
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
--More-- or (q)uit
Next Boot License Type........................... Permanent
Configured Country............................... GB - United Kingdom
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +25 C
External Temperature............................. +31 C
Fan Status....................................... 4000 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 44:03:A7:AA:BB:CC
Maximum number of APs supported.................. 25
- Reload
The controller now has the code update in active volatile RAM, but you must enter reset system to save the code update to non-volatile NVRAM and reboot the Cisco Wireless LAN Controller:
reset system The system has unsaved changes. Would you like to save them now? (y/n) y
- Verify at booting
(Cisco Controller) >
Updating license storage ... Done.
Restarting system.
WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)
Board Revision 0.0 (SN: PSZ17012345, Type: AIR-CT2504-K9) (P)
Verifying boot loader integrity... OK.
OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz data rate)
CPU Cores: 4
DRAM: 1024 MB
Flash: 32 MB
Clearing DRAM........ done
Network: octeth0', octeth1, octeth2, octeth3
' - Active interface
E - Environment MAC address override
CF Bus 0 (IDE): OK
IDE device 0:
- Model: 1GB CompactFlash Card Firm: CF B612J Ser#: A191102621A10AABBCCD
- Type: Hard Disk
- Capacity: 977.4 MB = 0.9 GB (2001888 x 512)
Press <ESC> now to access the Boot Menu...
Cisco AireOS Version 7.5.102.9
Firmware Version PIC 16.0
Initializing OS Services: ok
Initializing Serial Services: ok
Initializing Network Services: ok
Initializing Licensing Services:
License daemon start initialization.....
ok
License daemon running.....
Starting Statistics Service: ok
Starting ARP Services: ok
Starting Trap Manager: ok
Starting Network Interface Management Services: ok
Starting System Services: ok
Starting FIPS Features: ok : Not enabled
Starting Fastpath Hardware Acceleration: Starting Switching Services: ok
ok
Starting Fastpath Console redirect : ok
Starting Fastpath DP Heartbeat : ok
Fastpath CPU0.00: Starting Fastpath Application. SDK-1.8.0, build 269. Flags-[DUTY CYCLE] : ok
Fastpath CPU0.00: Initializing last packet received queue. Num of cores(2)
Fastpath CPU0.00: Init MBUF size: 1856, Subsequent MBUF size: 2040
Fastpath CPU0.00: Core 0 Initialization: ok
Fastpath CPU0.00: Initializing Timer...
Fastpath CPU0.00: Initializing Timer...done.
Fastpath CPU0.01: Core 1 Initialization: ok
Starting QoS Services: ok
Starting Policy Manager: ok
Starting Data Transport Link Layer: ok
Starting Access Control List Services: ok
Starting System Interfaces: ok
Starting Client Troubleshooting Service: ok
Starting Management Frame Protection: ok
Starting Certificate Database: ok
Starting VPN Services: ok
Starting DNS Services: ok
Starting Licensing Services: ok
Starting Redundancy: ok
Starting LWAPP: ok
Starting CAPWAP: ok
Starting LOCP: ok
Starting Security Services: ok
Starting Policy Manager: ok
Starting Authentication Engine: ok
Starting Mobility Management: ok
Starting Capwap Ping Component: ok
Starting AVC Services: ok
Starting Virtual AP Services: ok
Starting AireWave Director: ok
Starting Network Time Services: ok
Starting Cisco Discovery Protocol: ok
Starting Broadcast Services: ok
Starting Logging Services: ok
Starting DHCP Server: ok
Starting IDS Signature Manager: ok
Starting RFID Tag Tracking: ok
Starting RF Profiles: ok
Starting Power Supply and Fan Status Monitoring Service: ok
Starting Mesh Services: ok
Starting TSM: ok
Starting CIDS Services: ok
Starting Ethernet-over-IP: ok
Starting DTLS server: enabled in CAPWAP
Starting CleanAir: ok
Starting WIPS: ok
Starting SSHPM LSC PROV LIST: ok
Starting RRC Services: ok
Starting SXP Services: ok
Starting Alarm Services: ok
Starting FMC HS: ok
Starting IPv6 Services: ok
Starting Config Sync Manager : ok
Starting Hotspot Services: ok
Starting Portal Server Services: ok
Starting mDNS Services: ok
Starting Management Services:
Web Server: CLI: Secure Web: ok
(Cisco Controller)
Enter User Name (or 'Recover-Config' this one-time only to reset configuration to factory defaults)